Whirlpool Compact Heat Pump Dryer FE Error Code
FE is a power source problem on compact heat pump dryers; check the outlet first.
Model Reference
Whirlpool WGD8120H Vented Gas Dryer Repair in San Francisco
Gas dryer owners often see no heat or a drum that stops, and the rear console usually shows why.
- 10 appliance guides
- 102 model pages
- 486 error codes explained
- 150 Bay Area places
- Mon–Sat 8:00 AM – 7:00 PM
Model number
WGD8120H
About this model
Model overview
The Whirlpool WGD8120H is a gas dryer with an 8.8 cubic foot powder-coated drum inside a 29-inch-wide cabinet. Its touchpad sits on the rear console, and three sensors adjust drying time from moisture and temperature. Steam wrinkle protection keeps tumbling for up to 150 minutes after the cycle, so the dryer can run well past the point the clothes are dry. In the Bay Area, owners most often call about no heat, a drum that does not turn, or squealing. On covered units, the control board pair is the first thing a technician looks at. In the booking form, name the symptom, copy the full number from the rating label, and add any code the rear console shows.
Specifications
| Dimensions | Width is 29 inches. |
|---|---|
| Capacity | Drum capacity is 8.8 cubic feet. |
| Features | The drum is powder coated. The side-swing door is reversible. Three sensors monitor moisture and temperature to adjust drying time. Steam wrinkle protection continues tumbling for up to 150 minutes. |
| Controls | Touchpad controls are located on the rear console. |
| Care | For covered units needing both control boards replaced, the service pointer instructs technicians to replace the HMI first and allow three minutes of powered operation before replacing the ACU. |
What sets the WGD8120H apart
The powder-coated drum holds 8.8 cubic feet and sits behind a reversible side-swing door, which lets the opening face the side the room needs. The touchpad is on the rear console rather than the front, so the controls are reached from the back of the unit. Steam wrinkle protection adds up to 150 minutes of tumbling after drying. Day to day, the rear controls and the long post-cycle tumble are the two details that set this dryer apart.
What owners notice
- No heat or overheating.
- Squealing, thumping or grinding.
- Drum not turning.
- Cycle ends too early.
Service notes for the WGD8120H
No heat on this gas dryer is checked at the igniter, the flame sensor and the gas valve, with the gas supply confirmed open first. A drum that does not turn is traced to the belt and the drive motor. A cycle that ends early points to the three sensors and their wiring. Where a covered unit needs both control boards replaced, the service pointer says to replace the HMI first and let the powered unit run for three minutes before replacing the ACU. Squealing or thumping is checked at the rollers. An owner can clear the lint screen, confirm the gas valve is open, and close the door fully.
Booking
We confirm the full model number, test the parts linked to the symptom and give a written estimate. Nothing is repaired without your approval. Related pages: Whirlpool Dryer Repair in San Francisco and Whirlpool Dryers.
Frequently asked questions
Yes, the side-swing door is reversible, so it can be set to open on either side.
Steam wrinkle protection continues tumbling for up to 150 minutes after the cycle.
Check the rating label around the door opening or on the back panel. Copy every letter and digit, including the ones at the end.
Yes. We book in-home visits for this model in San Francisco and the Bay Area. Add the model number and the symptom to the booking form.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Diagnostics
Error codes for this appliance
Fix it right
Repair service
Dryer Repair in San Francisco
Gas, electric and ventless Whirlpool dryers diagnosed across San Francisco and the Bay Area, with a written estimate before any repair begins.
Models
Other models
Book a repair
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Phone
(415) 687-4102
Hours
Mon–Sat: 8:00 AM – 7:00 PM
Service area
San Francisco Bay Area, California