Whirlpool Compact Heat Pump Dryer FE Error Code
FE is a power source problem on compact heat pump dryers; check the outlet first.
Model Reference
Whirlpool WGD5000DW Gas Dryer Repair
A 27-inch gas dryer of 7.0 cubic feet. Heat and vent faults are the usual reasons for a visit.
- 10 appliance guides
- 52 model pages
- 486 error codes explained
- 150 Bay Area places
- Mon–Sat 8:00 AM – 7:00 PM
Model number
WGD5000DW
About this model
Model overview
The WGD5000DW is a Whirlpool gas dryer, listed at 7.0 cubic feet and 27 inches wide. Because it burns gas to make heat, it deserves two kinds of care: the usual dryer airflow checks and a few gas-specific habits.
Gas safety comes first
If you smell gas, leave the home, touch no switches, and call the gas utility or 911 from outside. Do not look for the leak yourself. A burning smell or sparks means power off at the breaker. Owners may check that the gas valve behind the dryer is in the open position, nothing more; fittings are not for homeowners to touch.
No heat or slow drying
When a gas dryer tumbles but stays cool, the cause could be the igniter, the flame sensing parts, the gas valve coils or a restricted exhaust that trips a safety. Read Whirlpool dryer not heating for a sensible order of checks. A dryer that runs hot but takes several cycles often has a vent problem long before it has a heating one.
The vent run in Bay Area buildings
Many San Francisco laundry closets send the vent through a long wall run with elbows, and lint builds where the duct turns. Clean the lint screen after each load, check the outside vent hood flap opens when the dryer runs, and straighten a crushed transition duct behind the machine. These are outside checks; a technician handles anything beyond them.
Codes
Dryers can report an airflow problem in several ways; a clogged lint screen or vent shows as F4 E3 on some controls. A line power concern reads F4 E4. For other displays see Whirlpool dryer error codes.
Next steps
See the lineup in Whirlpool dryers and book through Whirlpool dryer repair. We diagnose before repairing, give a written estimate, and repair nothing without approval.
What a visit covers
The technician confirms the symptom, inspects the vent run and the lint path, then follows the heating sequence on a gas dryer. You hear what was found and receive a written estimate. If a part is needed, nothing is ordered or installed until you agree, and you decide whether to repair or replace.
Frequently asked questions
Our model data lists it as gas. Confirm the gas valve position at the wall, but do not touch the fittings.
Several causes fit that symptom, from the ignition parts to a clogged vent. A technician narrows it down on site.
Clean the lint screen every load. For the duct, how long the run is and how many turns it has matter; a technician can assess it during a visit.
If it smells of gas, no. If it only heats poorly, limit use and watch for hot surfaces.
Usually in the dryer door opening. See finding a Whirlpool model number for typical spots.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Diagnostics
Error codes for this appliance
Fix it right
Repair service
Dryer Repair in San Francisco
Gas, electric and ventless Whirlpool dryers diagnosed across San Francisco and the Bay Area, with a written estimate before any repair begins.
Models
Other models
Book a repair
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Phone
(415) 687-4102
Hours
Mon–Sat: 8:00 AM – 7:00 PM
Service area
San Francisco Bay Area, California